Napište, co zařízení dělá, nebo si závadu vyberte z přehledu níž.
The display shows no data.
- Příčina
- The boiler is not connected to the network.
- Řešení
- Connect the boiler to the electrical power network (230V/50Hz) with appropriate cable with plug.
The worm feeder doesn't work.
- Příčina
- The cable of the engine is disconnected / damaged.
- Řešení
- Connect the engine / change the cable to the engine.*
The thermal protection of the engine was activated repeatedly.
- Příčina
- The engine was overheated and the thermal protection was activated.
- Řešení
- Let the engine cool down, after cooling the engine will start again.
The boiler drive is working, but the worm feeder doesn't work
- Příčina
- The worm feeder is blocked (stone, etc.)
- Řešení
- Dismantle the worm feeder and remove the problem. Re-assemble the device.*
The worm gear is moving but the fuel is not being transported into the combustion area.
- Příčina
- There is no fuel in the container.
- Řešení
- Fill the container with recommended fuel.
The boiler ventilator doesn't work.
- Příčina
- The cable of the ventilator has been disconnected / damaged.
- Řešení
- Connect (change) the cable to the ventilator.*
The ventilator is noisy.
- Příčina
- The ventilator is broken.
- Řešení
- Change the ventilator.*
During the boiler modulation at the lowest output, the ventilator does not turn.
- Příčina
- The set values of ventilator speed (revolutions) are too low.
- Řešení
- Increase the values of the ventilator turns so that continuous operation of the ventilator is ensured.
The water from the emergency extinguishing system runs in the fuel container.
- Příčina
- The fuel has burnt off in the fuel container and the thermostatic valve was opened.
- Řešení
- Remove the wet fuel from the boiler, refill the container with the new fuel and put the boiler into the operation.
The water from the emergency extinguishing system drops in the fuel container.
- Příčina
- The paraffin plug is not tight.
- Řešení
- Change the thermostatic valve.
Water drops appear on the walls of fuel container.
- Příčina
- Wet fuel is used in the boiler.
- Řešení
- Fill the container with dry fuel.
The boiler can't reach the full nominal capacity.
- Příčina
- The time from the firing was too short.
- Řešení
- Let the boiler fire up properly.
The exhaust gas temperature is higher than is recommended in the user's manual.
- Příčina
- Different fuel used (high humidity, heating power etc.).
- Řešení
- Fill the container with appropriate fuel.
Smoke appears in the fire room or in the fuel container.
- Příčina
- The ceramic reflector is not installed in the boiler.
- Řešení
- Install the ceramic reflector according to the user's manual.
The boiler is coated with smoke particles in a short period of time.
- Příčina
- Fire door and/or the upper boiler cover and/or the fuel container cover are not closed properly.
- Řešení
- Close the fire door and/or the upper cover of the boiler and/or the fuel container cover.
The boiler is repeatedly overheated
- Příčina
- The boiler is repeatedly overheated
- Řešení
- Set the boiler capacity to the nominal capacity (see Instruction Control Unit manual).
The ash on the grate forms clogs.
- Příčina
- The grate is full of dust and ash.
- Řešení
- Clean the grate.
A great quantity of unburned fuel appears in the ashtray.
- Příčina
- Recommended fuel was not used for burning.
- Řešení
- Fill the container with appropriate fuel (see chapter 3).
Nic jsme nenašli. Zavolejte nám – závadu určíme.
Informativní přehled z manuálu výrobce. Posouzení a opravu vždy svěřte servisnímu technikovi.
